Birds

Materials...

• Fabric, you don't need much, a piece about the size of an A4 sheet of paper should be enough for the actual birds. Of course you need about three times as much to account for all the bits that you will bugger up. Cotton or linen is much easier to work with than silk. I used dupion silk which didn't pucker like silk satin would but it did fray a lot and it was quite easy to pull the fabric.
  

• A polystyrene ball, about 4cm across. To throw at anyone who offers 'helpful' suggestions.
  

• Wire, about 1mm thick. To poke said person.

• Dressmakers pins to hold everything together, including your sanity. I didn't have any when I made Norma Jean and I nearly lost my mind trying to hold the pieces together and sew them at the same time. If you're using white fabric be careful of old or cheap pins which are quite often tarnished and will leave marks on light coloured fabric.
  

• Feathers, if you want a feathery tail. Preferably from an ethical source.
  

• A kebab skewer or cocktail stick, painted or coloured whatever beak colour tickles your fancy. I've also heard of people using golf tees, but I don't like plastic. Or golf.
  

• An outfit of some sort or another which will be very handy in covering your mistakes. And the blood stains from where you prick your finger and don't notice until after you have smeared blood all over the expensive white silk that has taken three days to fashion into a bird shape.
  

• Stuffing. I used filter wool from The Boy's fishkeeping supplies as it's almost identical to the polyester stuffing you can buy for the purpose and he didn't want it.
  

Sewing...

I'm really bad at working to a pattern, I tend to cut bits out then pin and tuck and fold until they are the right shape, but I did figure out some basic shapes that worked as a starting point -

Part B is the body and the dotted line marks the bit that is actually visible at the end, but I discovered that you need a lot of extra fabric to play with to get the right shape and to leave room for stuffing the bird.

Parts A and C are the sides of the bird, again the bottom half is little like the actual shape that is sewn but it was much easier to have extra.

Sew part A to part B first, up to point (a)

then part C to part A, up to point (b)

then finally parts A and C to each other, to point

(are you following this?!)

The point where the three pieces come together to make the top of the head was a right nightmare and required a lot of fiddling about to get it lying right.

Then stuff the top half of the bird with whatever stuffing you're using. Put the polystyrene ball in at the fattest part of the body then fold and tuck the three pieces of fabric until it all looks bird shaped, holding everything in place with the dressmakers pins. The ball will do all in its power not to stay in the bird. Hold the f*cker in with pins while you sew it all up. I left quite a few pins in the bird, holding part B to the polystyrene ball, they were all covered up with other bits of fabric or will be covered up when I put a dress on her. Pins are your friend while doing this project, use them liberally!


Remember to leave the end of the body open for a tail)

Features....

It is a good idea to figure out the placement of the eyes and beaks with pins first, pushing them in to make features and work out the spacing. They are a lot less permanent that thread or the hole that a beak will leave should you decide it's in the wrong place. And pins leave handy little holes as guides for where to sew.

I sewed eyes on with thin black thread, essentially making a knot and then sewing over the top of it until they were the right size and shape.

Poke a hole in the face with a pin and wiggle it about a bit before trying to put the beak in as it is very easy to pull the fabric while trying to get it in. We made our beaks with wooden kebab skewers, cut to about an inch long and whittled at both ends so they were easier to poke through the fabric, and coloured in with permanent marker. Make sure you leave it plenty of time to dry before putting it anywhere near your white fabric....



Legs....


We made legs out of pieces of wire about 10 inches long and bent feet at one end. The Boy patented a three 'toe' system (do birds have toes? Are they called something different? I've never heard anyone mention birds having toes.....) which made the legs stable enough to hold the bird up.

The wire was bent like this, starting at point A

...and at point B (my favourite part of this whole 'instructions' process is labelling!) the wire was bent straight up to make a leg, then cut them to the right length for your birdie, leaving about an inch to be put into the body.

We wrapped the legs in embroidery thread as I thought the wire was 'too shiny'. We tried wrapping them in thin black wire but it was 'too ugly'. I super glued down the tufty bits of thread at the top of the legs. Super glue dries faster than you might think. Pulling legs off your fingers is more painful than you might think. Just sayin....

Then we shoved them rather forcefully into the body, through the many layers of fabric and into the polystyrene ball. This bit was quite difficult and I bent the legs over and over again. Using a really big needle to make a hole before trying to get the legs in is a good idea, as is trimming the end of the wire into a sharp point with wire cutters.

Wings...

I made the wings by cutting out cardboard wing shapes, wrapping them in a very thin layer of stuffing (glued on) then wrapping them in fabric which I sewed together at the back, very messily.

See?

Then I sewed them in place with a few tiny stitches round the edges. You could of course use glue instead. Boy Bird's are done but Girl Bird's are waiting until after she is dressed. Boy Bird's are slightly bigger, at the request of The Boy....

Tail....

The tail was surprisingly easy to sew together, I made the feathers into a little bunch first, tying them with thread, then poked them into the hole, tucked the fabric under and sewed it all up. Feathers are quite difficult to arrange, they seem to have a mind of their own, so the tails aren't quite as flat as I would have liked, but that gives them character me thinks.

You could also make tails in a similar fashion to the wings, with cardboard and fabric, if you didn't want to use feathers.

(You can see the hole left at the bottom of Boy Bird for the tail feathers. You can also see my dodgy sewing in the delightfully squint seam running down Girl Bird's back. That, along with the blood stain a couple of inches above her tail will be covered with the offcuts of my dress though. Phew)




He stands up all by himself. I was most surprised at this! But I think we're going to stick them to a little base to sit atop our stack of cupcakes on glass stands, just in case they fall over. Because they're not that stable.



Dressing.






Do this before putting the legs on. For my first bird I used a length of lace about 4 inches wide and 8 long and wrapped it around until it looked alright. Then I used a couple of small stitches to hold it in place. Same for the veil. For the veil I used a bit about 4 x 4 inches.


I think that's everything. You're on your own now. (I am only joking of course, if you have any questions please do ask and I'm um and ah a bit before telling you 'left a bit, no right a bit. Well I don't know, do I?' )

And there you have it. Not quite as chic and flawless as their $300 counterparts